Best Electric Wall Heaters for Bathrooms and Small Rooms
Top pick: Stiebel Eltron CK 15 E (120 V, 1500 W, surface-mounted)
Buy the Stiebel Eltron CK 15 E for a bathroom, bedroom, office or basement room on a 120 V circuit. It wins on the points that decide this purchase. Stiebel names bathrooms among its intended uses. Its built-in thermostat covers 41–86°F and has a frost-protection setting. Stiebel rates the blower at 49.7 dB(A). It is certified to ANSI/UL Std. 2021 and conforms to CAN/CSA C22.2 No. 46, and Stiebel backs it with a 3-year limited warranty. Retail listings put it at about $130–160.
Get Stiebel Eltron CK 15 EStiebel’s figures for the CK 15 E: 1500 W, 12.5 A and 5,122 Btu/hr. An 18 W shaded-pole motor drives a galvanized squirrel-cage blower, and a nichrome wire element works with a bimetal thermostat and a high-limit switch. The body is 18-1/8 in high, 13-3/16 in wide and 4-13/16 in deep, and weighs 8.0 lb. It mounts on the surface of the wall rather than in a stud-bay can, so nothing has to be cut out of a tiled or finished wall. The trade-off is a box that sticks out almost 5 in from the wall. It is hardwired only, with no cord. Stiebel’s manual warns that the casing and the air it blows out get hotter than 194°F, so bare skin must not touch them; that the heater must never be covered or have its air openings blocked; that furniture, bedding, clothes, curtains and other combustibles must stay at least 3 ft from its front, sides and rear; and that it must never run outdoors or in a room at risk of fire or explosion from chemicals, dust, gases or vapors. Stiebel specifies a 15 A breaker and 12 AWG wire. Stiebel warns that a heater run from a time switch can keep heating the room unchecked, so it must be supervised constantly in a small room whose occupants cannot leave on their own, and that children or people with limited physical, sensory or mental capabilities may control it only under supervision or after instruction.
Who should not buy it: for a room over 150 sq ft, or a house with a spare 240 V circuit, get the Stiebel Eltron CK 20 E instead. Stiebel rates it at 2000 W and about 6,800 BTU/h at 240 V, and 1500 W at 208 V. The same CK manual warnings apply, and Stiebel says the voltage on the type plate must match the mains voltage. If you want a 60-minute full-output boost that then hands control back to the thermostat, pay more for the timer version, the CKT 15 E, which Home Depot lists at about $169. On the CKT’s timer the heater runs at full output without temperature control, and Stiebel warns that a heater on a time switch can keep heating the room unchecked: supervise it constantly in a small room whose occupants cannot leave on their own. If you want a grille set flush into the wall instead of a box on its surface, buy the Cadet below.
Get Stiebel Eltron CK 20 EThese picks were not tested. The ranking comes from the makers’ specifications and installation manuals plus retail listings, and each figure on this page names its source.
The rest, ranked: in-wall, multi-voltage and plug-in heaters
2. Cadet Com-Pak Bath CBC103TW: the in-wall bathroom heater with a timer. Cadet built this one for bathrooms. It has a built-in single-pole thermostat and a 60-minute timer. Cadet says a coating on the heating element prevents rust in a damp room. A centrifugal blower runs on an impedance-protected motor, and a high-temperature safety shutoff is built in. Cadet rates it at 1000 W (3,415 BTU/h) on either 120 V (8.3 A) or 240 V (4.2 A). The galvanized 20-gauge wall can needs a rough-in opening 8 in wide, 10-1/8 in high and 4 in deep. Listings run about $175–260.
Get Cadet Com-Pak Bath CBC103TWBuy it for a bathroom of up to about 100 sq ft (10 W per sq ft) where you want the heater recessed between the studs and value the timer more than raw output. Do not buy it for a bedroom or office: 1000 W is two-thirds of the Stiebel’s output, and a timer only pays off in a room used in short bursts. Cadet’s owner’s guide says to mount it with the element up and at least 24 in below the ceiling, never in a floor or ceiling, below a towel bar, behind a door or anywhere the air discharge may be blocked; to keep furniture, drapery, cords and other combustibles at least 3 ft from its front and away from its sides and rear; and to take extreme caution when it is used near children or invalids or left running unattended. Watch one setup trap. Cadet ships this multi-volt heater set for 240 V. To run it on 120 V, its owner’s guide has the installer move the blue wire from terminal D to terminal A and connect the spare red wire to terminal D. Cadet warns that a heater set for 120 V and connected to 240 V is destroyed and could start a fire. A heater set for 240 V and connected to 120 V puts out far less heat: resistive heat scales with the square of the voltage, so it gives about a quarter of its rating.
3. King Electric W1215-T-W: the in-wall heater wired at installation for 1500 or 750 W. King rates it at 120 V with a choice of 750 W or 1500 W (6.3 or 12.5 A). It has an open-coil nichrome element, a four-blade fan moving 85 CFM and a built-in single-pole thermostat. The wall can has QuickSet tabs that line it up on a stud. It has King’s Smart Limit overheat protection and a UL listing, and it is made in the USA. Listings price it at about $210–235.
Get King Electric W1215-T-WBuy it for a bedroom, addition or basement room with an open stud bay that needs up to 1500 W. King’s 750 W half-wattage setting (6.3 A) is a field modification made at installation, not a seasonal switch. King’s installation instructions give minimum clearances of 36 in in front, 12 in above, 4 in to the floor and 6 in to a side wall. Do not put the standard W1215-T-W anywhere water can splash: King says the W series gets a UL wet-location rating only when installed in its WSC surface can. King gives the W series a 2-year limited warranty.
4. Broan 174: one heater for 120, 208 or 240 V. Broan wires it at the factory for 1500 W at 120 V (12.5 A), and it can be rewired for 750 W at 120 V, 1125 W at 208 V or 1500 W at 240 V. It has a snap-action bimetal thermostat on the front, a nickel-chrome element insulated with mica, and a 24-gauge steel housing behind a 20-gauge, 12 in grille. Louvers push the heat downward, a thermal overload must be reset by hand after it trips, and the heater is UL listed. Listings price it at about $200.
Get Broan 174Buy it if the circuit voltage is not settled yet, or if one model has to serve rooms on different supplies. The drawbacks are in Broan’s manual. It may only be installed horizontally in a wall, at least 6 in from the floor or any adjacent wall. Its manual also says installation and wiring must be done by a qualified person, the heater must be grounded and must not be connected to a dimmer switch or speed control, combustibles such as furniture, bedding, clothes and curtains must stay at least 3 ft from its front, it must not be used where gasoline, paint or flammable vapors or liquids are used or stored, and extreme caution is needed near children or invalids or when it is left running unattended. The limited warranty lasts one year, and Broan requires notice within seven days of finding a defect. That is the shortest coverage here, which is why it ranks below the King.
5. Envi LE5012P: the plug-in panel for renters. The third-generation Envi from eheat is a fanless convection panel. eheat’s figures: 500 W at 120 V, 4.17 A, a 6 ft cord, a manual thermostat, and a body 19.3 in wide, 22.2 in high and 2 in deep that weighs about 10 lb. A built-in wall switch (eheat calls it wall-sens) keeps the heater off unless it is clipped to the wall with the supplied brackets. eheat rates the 500 W model for rooms up to 150 sq ft and says it can go in a bathroom outside the splash zone. The warranty is 3 years. eheat’s manual says to plug it only into a properly grounded outlet and never defeat the grounded plug, never to block its air intakes or exhaust or let liquid enter it, not to use it outdoors, and to take extreme caution when it is used near children or invalids or left running unattended.
Get Envi LE5012PBuy it where you cannot run a new circuit: a rented bedroom, a home office, or a small bathroom that needs steady background warmth. Do not buy it to warm a cold bathroom fast before a shower. At 500 W it puts out about 1,706 BTU/h, a third of a 1500 W fan heater, and without a fan the heat spreads slowly by convection. It keeps a warm room warm; it does not heat a cold one quickly.
Sizing: watts, BTU/h and the room size the maker states
Every resistive heater turns 1 W into 3.412 BTU/h, so wattage alone sets the output: 500 W gives about 1,706 BTU/h, 1000 W gives 3,412, 1500 W gives 5,118 and 2000 W gives 6,824. None of these heaters turns electricity into heat more efficiently than another. The differences are how fast the fan spreads the heat and how steadily the thermostat holds the set temperature.
The usual sizing rule for supplemental electric heat is about 10 W per square foot of floor in a room with an 8 ft ceiling. A bathroom with an outside wall, a tile floor or a window over the tub loses heat faster than the rule assumes. In a 60–100 sq ft bathroom like that, choose 1500 W over 1000 W. Above about 250 sq ft, one wall heater of this size is the wrong tool; the best space heaters for large rooms cover that job.
Voltage changes the current, not the heat. A 1500 W heater draws 12.5 A at 120 V but only 6.25 A at 240 V, which is why 240 V models can run on smaller wire. A 240 V element on a 208 V supply, common in apartment buildings, delivers about 75% of its rating because heat scales with the square of the voltage. Broan lists the 174 at 1125 W on 208 V, and Stiebel lists the CK 20 E at 1500 W on 208 V. Check which voltage the building has before choosing a wattage.
Wiring: dedicated circuits, breaker sizing and who installs it
Four of the five picks are hardwired. Cadet’s owner’s guide for its standard Com-Pak (not the Com-Pak Bath) says electric heaters must be on a circuit dedicated to electric heaters and cannot share it with outlets, lights or other appliances; plan the same for the Stiebel, King and Broan. A 120 V heater uses a single-pole breaker. A 240 V heater uses a double-pole breaker and a cable with two hot conductors. Where the local code requires it, an electrician installs the heater and pulls any permit; Stiebel’s manual says a qualified installer should carry out the installation, electrical connection and first operation, and only licensed electricians should maintain or repair it.
Breaker size: the National Electrical Code (Article 424) treats fixed electric space heating as a continuous load and sizes its circuit at 125% of the heater’s rated current. For a 1500 W heater at 120 V that is 12.5 A × 1.25 = 15.6 A. Stiebel lists a 15 A breaker with 12 AWG wire for the CK 15 E. A 12 AWG run is also rated for a 20 A breaker, and the local inspector decides which breaker the code in force requires. For a 2000 W heater at 240 V the same sum gives 10.4 A, which fits a 15 A circuit.
Thermostat placement: a built-in thermostat reads the air at the heater, which usually sits low on the wall. The Stiebel, Cadet, King W1215-T-W, Broan 174 and Envi all have one. Stiebel notes that in rooms larger than 215 sq ft the CK can run from an ordinary wall-mounted room thermostat instead. King sells the W1215 without the -T suffix (no built-in thermostat) for use with a separate wall thermostat. That is the better setup when the heater has to go in a cold corner or near a draft that would fool a built-in sensor. The Cadet Com-Pak Bath is the exception: Cadet says it is not to be used with a wall thermostat.
Bathroom placement: what each manual allows
Broan’s manual forbids installing the 174 in a tub or shower enclosure, or anywhere it may come into contact with water. It also says a switch must never be placed where someone in the tub or shower can reach it. The heater goes in horizontally, at least 6 in from the floor and from any adjacent wall.
Stiebel’s CK manual requires the controls to be out of reach of a person in the bath or shower. It tells the installer to respect the safety zone printed on the heater’s type plate, and it calls for a vertical wall that can withstand at least 194°F. The heater must never sit directly below a wall socket. The manual’s clearance drawing gives 4 in from the floor as the minimum and recommends 6–8 in.
King’s standard W series is not wet-location rated on its own; only the WSC surface can adds that UL rating. Cadet handles bathroom humidity on the Com-Pak Bath with its painted element, but its owner’s guide forbids installing the heater directly above a bathtub or sink or in a shower stall area and recommends keeping it at least 2 ft away to prevent contact with water. eheat allows the Envi in a bathroom only outside the splash zone and where local electrical codes are followed. In a small bathroom where every wall is close to the tub, the usual spot is the wall opposite the tub or beside the door. Keep it out of the door’s swing, because a door that opens against the grille blocks the airflow every time.
What is not worth the money, and how wall heaters fail
Not worth paying for: a 2000 W, 240 V heater in a 40–60 sq ft half bath. At 10 W per sq ft that room needs 400–600 W, and an oversized fan heater switches on and off in short bursts. A timer on a bedroom heater adds cost for a feature built for 20-minute bathroom use. A plug-in panel is a poor buy where a circuit can be run: the Envi’s 500 W is a third of what a hardwired 1500 W heater delivers.
Lint and dust: a fan-forced heater pulls room air across the element, and bathroom towels shed lint that builds up on it. The Broan 174’s heater assembly lifts out of its housing for cleaning. Broan says to clean the heater once a month with the power off at the service panel and the element cool, and never to immerse its metal or electrical parts in water. Cadet’s Com-Pak heating unit is separate from the wall can and fastens to it with one screw, so a failed unit can be swapped without opening the wall. Cadet says the heater must be cleaned at least every six months, with the power off at the main panel.
Nuisance trips: a towel hung over a grille makes the heater overheat until the high-limit switch cuts power. On the Broan 174 that overload has to be reset by hand, with the power turned off at the service entrance before the knob and grille come off, so the heater stays off until someone resets it, and it can look like a dead heater. The Com-Pak Bath’s high-temperature shutoff also resets by hand, with a button behind a plug, after the power is off and the heater has cooled for 10 minutes; Cadet says not to tamper with it or run the heater without its grill, and to replace the heater if the shutoff trips more than once a day. Envi panels do the same if the wall-sens switch loses contact: the heater will not power on until it is clipped back onto its brackets.
Wrong voltage: a 240 V heater wired to a 120 V circuit runs at a quarter of its rating, so 2000 W becomes 500 W. A 120 V heater wired to 240 V burns out. Read the rating plate before the drywall goes back up.
Related guides
- AC and mini split coil-cleaning supplies: mini split cleaning kits and wash bags, no-rinse and foaming evaporator/condenser coil cleaners, fin combs, and soft brushes (by unit type: wall-mounted mini split indoor head, outdoor condenser, window AC)
- AC and mini split condensate management: condensate pumps, drain-line clog prevention and overflow protection
- Best Air Purifiers for Allergies (2026)
- Best Ceiling Fans for Large Rooms (2026)
FAQ
Is an electric wall heater safe to install in a bathroom?
Yes, if the model’s manual allows it and the installation follows that manual. Broan’s manual for the 174 rules out tub and shower enclosures and switches reachable from the tub. Stiebel requires the CK’s controls to be out of reach from the bath or shower. King’s W series is wet-location rated only in its WSC surface can.
Do I need an electrician to install a wall heater?
For the hardwired models, yes wherever local code requires it, and the circuit has to be dedicated: Cadet’s guide for its standard Com-Pak (not the Com-Pak Bath) says no outlets, lights or other appliances on it. A 240 V heater also needs a double-pole breaker. The Envi LE5012P is the exception: it plugs into a standard 120 V outlet and clips to the wall.
Should I buy a 120 V or a 240 V wall heater?
Buy the voltage of the circuit you have or will run. Heat output depends on watts, not volts; 240 V only halves the current, so 1500 W draws 12.5 A at 120 V and 6.25 A at 240 V. A heater wired for the wrong voltage either runs at about a quarter of its rating or, as Cadet warns for the Com-Pak Bath, is destroyed.