Best Line-Voltage Thermostats for Electric Baseboard Heat

Top pick: Mysa LITE for Electric Baseboard Heaters

Buy the Mysa LITE for Electric Baseboard Heaters if you live in the US and heat with baseboard, convector or fan-forced heaters on a 120 V, 208 V or 240 V circuit. Mysa rates it at 16 A maximum: 1,900 W at 120 V, 3,300 W at 208 V and 3,800 W at 240 V. Mysa says to install it on a 20 A breaker. It joins 2.4 GHz Wi-Fi directly and needs no hub.

Get Mysa LITE for Baseboards Get Mysa LITE for Electric Baseboard Heaters

This list sets five criteria: the load the maker rates the thermostat for, the heater types the maker says it can run, the wiring it needs in the wall box, what the app does without a subscription, and the maker’s warranty and price. The LITE does well on all five. The 3,800 W rating at 240 V covers two 1,500 W heaters with 800 W to spare. Mysa says it runs electric baseboards, short-cycle convectors, long-cycle fan-forced convectors and radiant ceilings. Sinopé’s TH1143WF and TH1144WF leave out fan-forced heaters. Mysa lists app control, schedules, shortcuts, geofencing and a temperature offset (firmware 3.17.1.2 or later), plus physical buttons on the unit and support for Apple HomeKit, Amazon Alexa and Google Home. Mysa’s app page says remote control, schedules and geofencing cost nothing extra. Mysa gives a 5-year limited warranty, which is longer than the 3-year warranty Sinopé’s guide gives, and Mysa’s own page lists the LITE at $99.00.

Get Sinopé TH1143WF Get Sinopé TH1144WF

Do not buy it if your wall box has only two wires. Mysa says the thermostat has to connect to both L1 and L2/Neutral to power itself. That means four wires in the box: two cables with two conductors each, not counting the ground. Skip it as well if you want room humidity readings or a chart of kilowatt-hours. Mysa states that the LITE has no humidity sensor, no Zones, no Saved Schedules and no Energy Over Time. Canadian readers face a different lineup: Mysa says its Gen3 baseboard model is sold in Canada, and the V2 and the LITE are the current US models.

These picks were not tested. The ranking comes from the makers’ published specifications, installation guides, owner’s manuals and store listings, and every figure on this page is the maker’s.

The rest, ranked: Sinopé and Honeywell Home

2. Sinopé TH1143WF: for a two-wire box, and for wattage readings. Sinopé rates the Sinopé TH1143WF at 12.5 A, which it gives as 3,000 W at 240 Vac and 1,500 W at 120 Vac, on 120, 208 or 240 Vac supplies at 60 Hz. It has two leads. Sinopé’s guide connects one to Line 1 and the other to Load 1, and notes that either lead can go to either wire, so there is no neutral or L2 connection to make. Sinopé lists a colour LCD, lockable buttons, detection of the connected load, geofencing and schedules, and consumption reports in its Neviweb app. Choose it over the Mysa LITE if your box has only two wires or if you want the thermostat to report the watts it is switching. Sinopé lists the body at 12.7 cm high, 8.6 cm wide and 3 cm deep, and its installation guide gives a 3-year limited warranty.

The TH1143WF has firm limits. Sinopé rates it for resistive loads only, says it cannot be used with a system controlled by a contactor or relay (inductive load) or a central heating system, and says it must be connected to a circuit protected by a 20 A (or lower) circuit breaker. Sinopé says it is not compatible with fan-forced heaters and works with electric baseboards, convectors, radiant ceilings and stand-alone hydronic baseboards. Its minimum load is 300 W, which is 1.25 A at 240 Vac or 2.5 A at 120 Vac, so a single small heater in a powder room may fall below it. It joins 2.4 GHz Wi-Fi only, and Sinopé says the 5 GHz band will not work. For a fan-forced (long-cycle) heater, Sinopé points buyers to the Sinopé TH1133WF. Sinopé rates that model at 12.5 A, 3,000 W at 240 Vac and 1,500 W at 120 Vac, and it needs a 3-wire connection. Sinopé says it must be installed by a certified electrician and rates it for resistive loads only. Its minimum load is 300 W at 240 Vac, or 500 W with a fan-forced convector, and Sinopé allows a maximum of one fan-forced convector per thermostat.

Get Sinopé TH1133WF

3. Sinopé TH1144WF: for one thermostat running more than 3,000 W. The Sinopé TH1144WF is the higher-capacity version of the same colour-display thermostat. Sinopé rates it at 16.7 A: 4,000 W at 240 Vac and 2,000 W at 120 Vac. Sinopé no longer sells the TH1124WF, which it rated at the same 4,000 W and 2,000 W. It has the same two-lead wiring, the same app features and the same exclusion of fan-forced heaters as the TH1143WF, and Sinopé gives it the same 300 W minimum load, resistive-load-only rating and 20 A (or lower) breaker requirement. Buy it when the heaters on one thermostat total more than 3,800 W and no more than 4,000 W at 240 V. That range is too much for the Mysa LITE but within this model’s rating. The extra capacity makes it bigger: Sinopé lists it at 11.5 cm wide and 3.2 cm deep, against 8.6 cm and 3 cm for the TH1143WF. Check that the wider body clears the trim beside the box.

4. Honeywell Home TL8230A1003: for a 240 V circuit, no Wi-Fi, and a switch that breaks both legs. The Honeywell Home TL8230A1003 is a LineVoltPRO 7-day programmable thermostat with a double-pole, single-throw (DPST) switch. Honeywell’s owner’s manual gives a 240/208 VAC supply and a maximum load of 15.0 A, which is 3,600 W at 240 VAC or 3,120 W at 208 VAC. It also lists a 40-86 °F setpoint range, a 15-minute heating cycle and three presets: Comfort at 70 °F, Economy at 62 °F and Vacation at 50 °F. Buy it if you want a schedule without an app account or a Wi-Fi network. Do not buy it for a 120 V heater, because the manual lists 240/208 VAC only. The manual also says to use it for resistive loads only, not to install it where it can be exposed to water or rain, to use special CO/ALR solderless connectors on aluminum wires, and to keep its top and bottom air vents clean and unobstructed. For more non-connected choices, see the best programmable thermostats without Wi-Fi.

Get Honeywell Home TL8230A1003

Sizing the load: watts, amps and the 208 V drop

The maximum load the maker states is the specification that matters most. Add up the nameplate watts of every heater wired to the thermostat. Dividing watts by volts gives amps. Two 1,250 W heaters on 240 V make 2,500 W, or about 10.4 A. That fits all four picks rated for 240 V: 3,000 W for the TH1143WF, 3,600 W for the TL8230A1003, 3,800 W for the Mysa LITE and 4,000 W for the TH1144WF.

The ratings are much lower at 120 V because the amp limit stays the same while the voltage is halved. Mysa’s 16 A becomes 1,900 W at 120 V, Sinopé’s 12.5 A becomes 1,500 W on the TH1143WF, and the TH1144WF’s 16.7 A becomes 2,000 W. A 120 V room with two 1,000 W heaters on one thermostat therefore needs the TH1144WF, or a second thermostat on part of the run.

Apartments and condos are often wired at 208 V, and a heater rated for 240 V does not deliver its full output there. Resistive heat falls with the square of the voltage: (208/240)² ≈ 0.75. A 2,000 W heater rated at 240 V gives about 1,500 W at 208 V. For sizing, use the 208 V figures the maker gives: 3,300 W for the Mysa LITE and 3,120 W for the TL8230A1003. Sinopé lists 208 Vac among its supply voltages but publishes its wattage limits only at 240 and 120 Vac. On a 208 V circuit, use the 12.5 A or 16.7 A limit and do the arithmetic: 12.5 A × 208 V ≈ 2,600 W for the TH1143WF.

The minimum load matters too. Sinopé sets 300 W as the floor for the TH1143WF. A single 250 W heater under a bathroom window is below that, and it needs a mechanical thermostat or a model whose maker documents a lower floor. If the heaters on a circuit add up to more than any thermostat here is rated for, split them across two thermostats rather than pushing one past its stated limit. That is rewiring at line voltage, and it is a job for an electrician.

Wiring: two wires, four wires, single-pole and double-pole

Before choosing, turn off the breaker, take off the old thermostat’s faceplate and count the conductors in the box, not counting the bare or green ground. Mysa’s wiring guide says to turn off the breaker, confirm with a voltage tester that the power is off, and photograph the existing wiring before touching anything. It also says to use the wire nuts that come with Mysa and not to use the old wire nuts again. Every thermostat on this page switches the full heater current at 120 V or 240 V. Sinopé says the TH1143WF, TH1144WF and TH1133WF must be installed by a certified electrician in conformity with local and national electrical codes, and Honeywell’s owner’s guide says installation of the TL8230A1003 must be carried out by a certified electrician. Mysa says some regions require an electrician to install a line-voltage thermostat, and that if you are unsure the power to your heaters is off, you should stop work and call an electrician.

Two conductors in the box. The supply comes in, passes through the thermostat and goes out to the heater. Sinopé’s TH1143WF and TH1144WF fit here because their two leads go in series with that conductor. Sinopé’s guide says special CO/ALR solderless connectors must be used on aluminum conductors and warns that a loose connection can pose a fire hazard. The Mysa LITE cannot be installed this way. It needs a fixed connection to L1 and to L2 or neutral, so it stays powered when the heater is off.

Four conductors in the box. There are two cables: one from the panel and one to the heater. At 240 V, Mysa’s guide connects L1 from the panel, L2 joined with the L2 going to the heater, and Load to the heater’s L1. At 120 V, the neutral replaces L2. Mysa notes that its thermostat is single-pole: it switches only L1 to Load, and the second connection is never switched. When several heaters are joined in the thermostat box, Mysa says the box must be large enough for the extra wires and wire nuts: “If the box is too crowded (‘box fill’), it can be dangerous.”

Single-pole and double-pole. A single-pole thermostat on a 240 V heater opens only one leg. When the display reads off, the other leg still connects the heater element to the panel. The heater stops making heat, but its terminals are not safe to touch. A double-pole thermostat such as the Honeywell Home LineVoltPRO model opens both legs, and Resideo’s thermostat selection guide lists the TL8230A1003 as 4-wire DPST with positive off. That is useful in a rental or a room where someone else might service the heater. It does not replace the breaker: whichever pole count you choose, switch off the breaker before opening a heater’s junction box.

Mounting. All four picks mount on a standard wall box over the old thermostat. Line-voltage thermostats are larger than 24 V ones, so measure the space against the maker’s figures: Sinopé gives 8.6 cm wide for the TH1143WF and 11.5 cm for the TH1144WF. Sinopé specifies indoor installation only.

Why a Nest or ecobee cannot run a baseboard heater

A Google Nest or ecobee thermostat is a low-voltage control. It switches 24 VAC signal circuits that tell a furnace, air handler or heat pump control board to start. A baseboard heater has no control board. The thermostat itself switches the 120 V or 240 V heating current, which can be 12 to 16 A. The terminals and switching parts of a 24 V thermostat are not built for that voltage or current. Mysa says low-voltage smart thermostats are not compatible with line-voltage baseboard heaters and can be dangerous if connected to them.

For the same reason, a heater’s wattage tells you nothing about whether a 24 V smart thermostat will fit. If the old thermostat has heavy stranded leads joined to house wiring with wire nuts, or a label giving a rating in amps or watts at 120/240 VAC, the circuit is line voltage. Only a line-voltage thermostat, such as the four picks here, belongs on it. Thin bell wire on screw terminals marked R, W, Y, G or C means a 24 V system. For those systems, the comparison you need is the best smart thermostats for 24 V systems.

Some homes have both: a central furnace or heat pump in the main rooms and baseboards in an addition or basement. These need two kinds of thermostat. Mysa sells products for both system types that run in one app. Sinopé also sells a Wi-Fi thermostat for 24 V central systems (TH6250WF) and runs its thermostats through its own Neviweb app. Mixing brands means using two apps unless both connect to a shared platform. Mysa lists Apple HomeKit, Amazon Alexa and Google Home support for the LITE.

What more money buys, and what is not worth paying for

On a line-voltage thermostat, paying more gets you three things: more amps, better data about the heat, and Wi-Fi control. The Honeywell Home TL8230A1003 has none of the app features. In return it has a double-pole switch, 7-day scheduling on the unit itself, and nothing to keep connected. The Mysa LITE adds app scheduling, geofencing and voice assistants. The Sinopé TH1143WF adds a colour display, a reading of the connected load and consumption reports. The TH1144WF adds 1,000 W of capacity at 240 V over the TH1143WF.

A higher amp rating is worth paying for only when the load needs it. On a 1,500 W heater at 240 V, the TH1144WF’s 4,000 W rating does nothing the TH1143WF cannot do, and it puts a body 2.9 cm wider on the wall. Buy capacity for the heaters you have. If a renovation will add a heater to the same thermostat, add its nameplate watts to the total before you buy.

Energy data is worth paying for if you will use it to change set-backs room by room. Sinopé’s consumption reports draw on a load-reading feature that Sinopé lists for the TH1143WF and TH1144WF. Mysa states that the LITE has no Energy Over Time chart. A household that sets one schedule and never opens the app does not need that data. One that pays time-of-use rates and wants to see which room is using the power does.

Do not pay for leftover stock of models whose makers have stopped making them. Sinopé no longer sells the TH1123WF and TH1124WF. It labels them end of line and names the TH1143WF and TH1144WF as their replacements. Do not count on a Zigbee version either unless you already run a Zigbee hub. Sinopé sells Zigbee variants (model numbers ending in ZB) that need one, while the WF models on this page connect directly to home Wi-Fi.

Get Sinopé TH1123WF Get Sinopé TH1124WF

FAQ

Can I use a Nest or ecobee thermostat with electric baseboard heaters?

No. Nest and ecobee thermostats switch 24 V control circuits, while a baseboard thermostat switches the heater’s full 120 V or 240 V current. Wiring a 24 V thermostat to a baseboard circuit destroys it and is a shock and fire hazard. Use a line-voltage smart thermostat such as the Mysa LITE or the Sinopé TH1143WF.

My wall box has only two wires. Which smart thermostat fits?

The Sinopé TH1143WF or TH1144WF. Sinopé wires their two leads in series between Line 1 and Load 1, and either lead can go to either wire. The Mysa LITE will not work: Mysa says it needs connections to both L1 and L2/Neutral, which means four conductors in the box, not counting the ground. Running an extra conductor to the box is a job for an electrician.

How do I check whether my heaters exceed a thermostat’s rating?

Add the nameplate watts of every heater on that thermostat and compare the total with the maker’s figure for your voltage. At 240 V, Mysa rates the LITE at 3,800 W and Sinopé rates the TH1143WF at 3,000 W. At 120 V, the same thermostats are rated at 1,900 W and 1,500 W. On a 208 V circuit, use the maker’s 208 V figure where it gives one, such as Mysa’s 3,300 W, or multiply the rated amps by 208.